How to read a bias point 01 Load a preset or paste a netlist. For a diode stage, replace the preset body with the netlist below and leave the .op directive in place. 02 Open Operating Point. The mode follows the .op directive automatically when you load a preset; otherwise pick the tab. 03 Read the node column (V(a), V(b), …) and the element column (I in amperes, P in watts) side by side. 04 Check the convergence line — Newton iterations and the residual — before trusting a nonlinear reading. 05 Compare against the schematic , then publish the table as a card or send it onward.
Worked readouts Paste this 1 kΩ diode stage and run Operating Point:
* 1N4148 bias point
V1 a 0 DC 0.8
R1 a b 1k
D1 b 0 1N4148
.op
Circuit
Readout
1 kΩ + 1N4148, V1 = 0.8 V
V(a) 0.8V , V(b) 0.52558V ; I(V1) −274.4µA , I(R1) 274.4µA , I(D1) 274.4µA ; P(V1) −220µW , P(R1) 75.3µW , P(D1) 144µW ; 12 Newton iterations, residual 2.26e-13
Resistive divider preset (10 V, 1 kΩ / 3 kΩ)
V(out) 7.5V ; I(V1) −0.0025A ; 1 iteration, residual 0.00e+0
Non-inverting amplifier preset (1 V, Rf 9 kΩ / Rin 1 kΩ)
V(out) 10V , node m 1V ; 1 iteration, residual 0.00e+0
BJT common-emitter preset
V(b) 1.8651V , V(c) 6.5314V , V(e) 1.1761V ; Q1 collector 2.486mA , I(B) 16.57µA ; 16 iterations, residual 8.94e-18
The linear stages converge in one iteration with a zero residual, while the two nonlinear stages need 12 and 16 — the iteration count is the price of the junction. The diode row balances by hand: 0.8 V across the branch, 0.52558 V held by the junction and 274.4 µA through 1 kΩ, and the two absorbing elements (75.3 µW + 144 µW ) account for the −220 µW the source supplies, to display precision.
Sign conventions in the table Branch currents follow the SPICE convention: positive current flows into the element's + terminal, so a source that delivers power reads negative — I(V1) is −274.4µA and P(V1) is −220µW , while R1 and D1 absorb 75.3µW and 144µW . Power is the passive sign product V·I, so resistors read positive and supplies read negative; the columns balance. A negative number is the direction, not a solver fault, and flipping it before comparing with a textbook will double the error.
Limits
First-order device models. Diodes use the Shockley equation with the built-in 1N4148 parameters, BJTs and MOSFETs are simplified; there is no temperature sweep, breakdown, noise, self-heating or parameter spread. Bias points are teaching-scale, not sign-off data.
Explicit failure, no silent answer. A circuit with no DC solution (a node reachable only through capacitors, a pure capacitive feedback) returns an error instead of a value; a failed Newton solve reports the residual it reached.
The 0.7 V trap Do not read a diode as a fixed 0.7 V drop. In the 1 kΩ stage above the junction settles at 0.52558 V — the rest of the 0.8 V falls across the resistor, and the exact split depends on the current. Run the same stage at V1 = 0.7 V and the junction holds about 0.51 V; the "0.7 V" figure is a rule of thumb for a different current, not a device constant. Read V(b), not the supply voltage.
Where it is useful Biasing a stage before the lab The BJT preset shows the whole common-emitter stage in one table: base 1.8651V , collector 6.5314V , emitter 1.1761V , collector current 2.486mA . Change Rb1, Rc or Re and watch the operating point move; the iteration line warns when a new bias is harder to solve.
Verifying a hand analysis Solve a divider on paper (7.5 V from 10 V through 1 kΩ and 3 kΩ), then check the table and the sign of I(V1). For a nonlinear stage, compare your assumed junction voltage with the printed V(b) and recompute the current from the printed branch value instead.
Privacy Netlists, solving and the schematic canvas all run in your browser; nothing you paste is uploaded.
References
Wikipedia, Diode modelling , en.wikipedia.org (访问日期:2026-10-07)— Shockley equation and its parameters.
Wikipedia, Newton's method , en.wikipedia.org (访问日期:2026-10-07)— iteration, convergence and residuals.
Wikipedia, SPICE , en.wikipedia.org (访问日期:2026-10-07)— netlist syntax and the .op directive.
Wikipedia, Kirchhoff's circuit laws , en.wikipedia.org (访问日期:2026-10-07)— nodal balance behind the node table.
Calculators in this hub
Hand-picked tools, one click away. The mini versions compute live and carry your values into the full calculator.
Sources & review
Reviewed by CalcX Editorial Team
Updated 2026-10-07