How to use it 01 Measure the wall face, not the bricks. Length × height minus openings gives the net face area; multiplying by wall thickness gives the net volume. 02 Pick the unit. Standard 240 × 115 × 53 mm is the default; the perforated 240 × 115 × 90 mm and AAC 600 × 200 × 250 mm presets are one click away. 03 Set the joint. 10 mm is the conventional bed and perpend for clay brick; AAC blocks use a 2–3 mm thin-bed adhesive instead. 04 Set waste and the mortar ratio. 3 % covers breakage and cutting; a 1:5 cement–sand volume ratio approximates an M5 masonry mortar. 05 Read the bricks and mortar together. The two cards are the same order — bricks plus the cement and sand bags to lay them.
Worked readouts A 6 m × 2.8 m wall, 0.24 m thick, with 1.8 m² of openings, standard brick, 10 mm joints, 3 % waste, mortar 1:5:
Card
The panel reads
Net wall volume
3.6 m³ (16.8 m² gross face − 1.8 m² openings)
Bricks per m³
507.937 (module volume 0.00196875 m³)
Bricks exact
1,828.57
Bricks to buy
1,884 (exact + 3 %)
Mortar volume
0.925 m³
Mortar cement
277.5 kg = 6 bags (50 kg bags)
Mortar sand
0.964 m³ ≈ 1,397 kg
The same wall with the AAC preset reads 112 blocks (108.09 exact + 3 % waste, rounded up) and 0.357 m³ of mortar (from the 108.09 exact count, not the 112 bought) at the panel's default 10 mm joint — but that bed is wrong for AAC: set the joint to its 2–3 mm thin-bed value and the same wall reads 122 blocks and 0.076 m³ , so leaving the default overstates the mortar more than fourfold.
Why the count is 508 and not 512 A brick alone occupies 0.240 × 0.115 × 0.053 = 0.0014628 m³, which would give 684 bricks per cubic metre — far too many, because bricks are not stacked in a solid block. Laid in a wall, each brick effectively occupies its size plus half a joint on every face: (0.240 + 0.010) × (0.115 + 0.010) × (0.053 + 0.010) = 0.00196875 m³. One divided by that module is 507.94 bricks per m³. The familiar "512 bricks per m³" comes from counting joints only in the two horizontal directions, which is right for a wall face but wrong for volume.
Mortar is then simply what the wall has left: wall volume minus the net brick volume, 3.6 − 1,828.57 × 0.0014628 = 0.925 m³ . That is more than a quarter of the wall's volume, which is why a brick order without cement and sand is half an order. The dry-material factor of 1.25 accounts for the voids in loose sand and cement, and the 1:5 ratio splits the dry volume into one part cement and five parts sand.
Assumptions and limits
Nominal dimensions and full joints. The count assumes every bed and perpend is exactly the joint width, so a 12 mm joint on the same wall drops the count to 481 per m³ and changes the mortar volume accordingly.
This is estimating, not structural design. The mix presets are site rules of thumb; load-bearing walls follow a designed mix and strength class, and the panel says so on the page. What it does not do: it does not handle reinforcement, bond patterns, lintels or openings at partial thickness, and it does not order anything. For concrete members use the Concrete panel , for surface finishes the Paint panel or the Tile panel .
The mortar is the surprise line item Most people check the brick count and skip the mortar. Here the bricks are 1,884 pieces, but the cement is 6 bags and the sand is nearly a tonne. Two inputs move that line fastest. The first is joint width: because the module multiplies three dimensions, going from 10 mm to 12 mm joints cuts the count to 481 per m³ , and 15 mm joints cut it to 444 per m³ , with the mortar volume rising in step. The second is openings: the panel subtracts their area at full wall thickness, so a garage door 2.5 m wide and 2.4 m high removes 1.44 m³ of masonry — more than a third of this wall — and the brick count falls with it.
Where it helps A garden wall before the first delivery Count the wall once and get bricks, cement and sand in the same pass; the shopping list copies out with quantities per line.
Comparing brick with block Switch the preset from standard brick to AAC: the brick count falls by an order of magnitude, and the mortar line depends on the joint you set — 0.076 m³ at a 2 mm thin bed, 0.357 m³ if you leave the 10 mm default.
Privacy Wall dimensions and estimates are computed in your browser; nothing is uploaded, and the shopping list is produced only when you choose to copy it.
References
Wikipedia, Brick , en.wikipedia.org (访问日期:2026-10-07)— nominal brick dimensions and the standard 240 × 115 × 53 mm unit.
Wikipedia, Brickwork , en.wikipedia.org (访问日期:2026-10-07)— bonds, courses and the role of the mortar joint in a wall.
Wikipedia, Mortar (masonry) , en.wikipedia.org (访问日期:2026-10-07)— cement–sand proportioning and why joints consume mortar.
Calculators in this hub
Hand-picked tools, one click away. The mini versions compute live and carry your values into the full calculator.
Sources & review
Reviewed by CalcX Editorial Team
Updated 2026-10-07